9S-4185 PLUG Caterpillar D10T 販売中 - モロッコ

税別価格
2,525 JPY
162 MAD
税別価格
2,525 JPY
162 MAD
[Other] 9S-4185 PLUG Caterpillar D10T

基本情報

機械カテゴリーその他部品
メーカー／型式9S-4185 PLUG Caterpillar D10T
機械の所在地Agadir
国
マスカス ID00F0AA4C
+ 詳細を表示
陸送・船積など見積もり・相談窓口

価格

通貨を選択
税別価格2,525 JPY  (162 MAD)
税金VAT（別）
税込み価格-

詳細

ストック番号9S-4185
メーカー／ シリアルナンバー9S-4185
納期EXW
その他情報Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The engine is equipped with an Electronic Control Module (ECM). The ECM contains no moving parts. Follow the troubleshooting procedures in this manual in order to be sure that replacing the ECM will correct the problem. Verify that the suspect ECM is the cause of the problem.Note: Ensure that the ECM is receiving power and that the ECM is properly grounded before replacement of the ECM is attempted. Refer to the schematic diagram.A test ECM can be used in order to determine if the ECM on the engine is faulty. Install a test ECM in place of the suspect ECM. Install the flash file with the correct part number into the test ECM. Program the parameters for the test ECM. The parameters must match the parameters in the suspect ECM. Refer to the following test steps for details. If the test ECM resolves the problem, reconnect the suspect ECM. Verify that the problem returns. If the problem returns, replace the ECM.Note: If an ECM is intended to be used as a test ECM, "Test ECM Mode" must be selected on the electronic service tool before the engine serial number is entered.Use the electronic service tool to read the parameters in the suspect ECM. Record the parameters in the suspect ECM. Install the flash file into the new ECM. After the ECM is installed on the engine, the parameters must be programmed into the new ECM.Note: When a new ECM is not available, an ECM can be used from an engine that is not in service. The ECM must have the same serial number suffix. Ensure that the replacement ECM and the part number for the flash file match the suspect ECM. Be sure to record the parameters from the replacement ECM. Use the "Copy Configuration ECM Replacement" function in the electronic service tool.
If the flash file and engine application are not matched, engine damage may result.
Perform the following procedure in order to replace the ECM.
Connect the electronic service tool to the diagnostic connector.
Use the "Copy Configuration ECM Replacement" function from the electronic service tool. If the "Copy Configuration" is successful, proceed to Step 4. If the "Copy Configuration" failed, proceed to Step 3.Note: Record any Logged Faults and Events for your records.
Record the following parameters:
Record all of the parameters on the "Configuration" screen.
Record all of the parameters on the "Throttle Configuration" screen.
Record all of the parameters on the "Mode Configuration" screen.
Record the serial numbers of the electronic unit injectors. The injector serial numbers are
STEP ABDELMOUMEN -
  • +212...表示
    販売店に問い合わせる際には「マスカスに掲載されている機械」とお伝えいただければ、スムーズにお取引いただけます。
  • WhatsApp
    +212 774693591
メール送信

販売主　姓／名前

  • A.　TYAL

    STEP ABDELMOUMEN -
    • +212...表示
      販売店に問い合わせる際には「マスカスに掲載されている機械」とお伝えいただければ、スムーズにお取引いただけます。
    • ...表示
      販売店に問い合わせる際には「マスカスに掲載されている機械」とお伝えいただければ、スムーズにお取引いただけます。
    • インスタントメッセージ連絡詳細：
    • WhatsApp
      +212 774693591
    • 対応言語：フランス語
    • Immeuble des forces Auxiliaires SAMLED，Avenue Mohammed V，80000 Agadir，モロッコ

会社

STEP ABDELMOUMEN -

2
マスカス利用年数
すべての出品機械
不審な掲載機械を報告
関連メーカー
メーカー出品数：
キャタピラー34207
ボルボ8961
リープヘル8785
コマツ（小松製作所）7088
JCB4321

マスカス・ジャパンで販売中の[Other] 9S-4185 PLUG Caterpillar D10T製その他部品です。この[Other] 9S-4185 PLUG Caterpillar D10Tの価格は¥2,525、-年製造です。この機械はモロッコのStep - Abdelmoumen, Agadir, より出品されております。マスカスには[Other] 9S-4185 PLUG Caterpillar D10Tの他にも他メーカーの機械も その他部品に多数出品されています。 詳細 - ストック番号：9S-4185, メーカー／ シリアルナンバー：9S-4185, 納期：EXW